Size Matters Most taps in the UK are said to be a standard size, but it’s worth remembering that the size refers to the way in which the tap fits onto the pipes rather than the size of the taps themselves (basin taps being 1/2″ and bath taps having 3/4″ threads).

What size is a standard tap fitting?

Step 1. Basin taps. Pictured is a basin tap, with a 15mm thread. Bath taps look very similar, except they have a 22mm thread and may be joined together as a mixer.

How do you measure a basin tap?

Getting the right size basin tap is not as easy as you may think. We always reckon that the spout should not come more than halfway into the lower bowl section of your basin. To make sure you do not go over this mark measure the distance between the center of tap hole to the niddle of the bowl section of your basin.

Are all taps universal fitting?

Not all

taps and countertop basins will be the same size, so you’ll want to make sure that there is adequate space from the top of your countertop basin to where the spout exits on the tap. Finally, make sure that you have enough space on your counter to mount your tap behind your basin.

What size is a basin tap hole?

Standard taps and spouts generally require a hole of at least 22mm in diameter. Monobloc mixer taps, taking both a hot and cold supply, mostly require a minimum 32mm diameter hole.

What is the difference between bath taps and basin taps?

While they may look the same, underneath they are not. Basin taps typically use a 1/2-inch pipe to connect the tap to the water supply. Whereas bath taps are capable of using more water, they have a 3/4-inch thread.

What size are basin tap connectors?

The 15mm and 22mm refer to the size of the supply pipe not the taps. However, as basin taps have 1/2″ and bath taps have 3/4″ threads you will have to use 15mm or 22mm connectors respectively.

Do you need a plumber to change taps?

Assuming you only need a plumber to install a new kitchen tap, you should expect them to turn off the water mains and remove the old faucet. In most instances, this job is straightforward and doesn’t require any additional pipes or plumbing.

What size are kitchen sink taps?

BSP SizeDiameter of the thread (mm)Typical products you might find1/2″20.9Shower hose, valves that screw into sink or basin taps, the rigid tails on basin taps, UK flexitail connectors3/4″26.4Bath tap rigid tails, valves that fit into bath taps1″33.21.25″41.9Basin wastes

How do I choose a basin tap?

  1. KNOW YOUR WATER PRESSURE. To get a decent flow of water from your taps it is vital that you choose ones that are appropriate for the water pressure in your home. …
  2. CHECK THE TAP HOLES. …
  3. SELECT THE STYLE. …
  4. WHAT’S IT MADE OF? …
  5. THE PERFECT FINISH.

Article first time published on

What are the best basin taps?

  1. Abode Fervour Wall Mounted Bathroom Tap. …
  2. John Lewis Marden Basin Mixer Bathroom Taps. …
  3. Moen Eva One-Handle High Arc Bathroom Faucet. …
  4. Hudson Reed Topaz Monobloc Basin Mixer. …
  5. Bristan Orta Basin Mixer. …
  6. Delta Lahara Lavatory Faucet. …
  7. Bristan Traditional Bath Taps.

What size are tap connectors UK?

The most standard tap thread for domestic taps in the UK is 3/4″ BSP. This measures 26.44mm across the outside diameter – roughly 1″ The picture shows the measurement for a standard 3/4″ tap thread. If your tap looks like this, you have a standard 3/4″ BSP tap.

Do bath and basin taps have to match?

Often, you can get your hands on a matching set of basin and bath taps, or even a pair bundled together. But if you’re seeking them separately, you want to make sure you get both a specific bath and basin tap as they’re not a one-size-fits-all deal.

Are all basin waste holes the same size?

First and foremost wastes are all the same size 1 1/4″ or 32mm. Sometimes people get confused and ask why is there 2 sizes of basin wastes? the simple answer is that they are 1¼” BSP (32mm) and bath/sink wastes are 1½” BSP (40mm).

What size is a standard bathroom sink drain?

While a bathroom sink’s design and overall size may vary from one model to the next, the drain holes are fairly standard, 1.25 inches being a general standard, with widths of 1.5 inches and 1.625 inches also common.

How do I know what size water pipe I have?

To find it, measure around the circumference of the pipe with flexible measuring tape. Divide the circumference by pi, or about 3.14159. For example, if the circumference is 12.57 inches (319 mm), you would divide by pi, and get an outside diameter of about 4 inches (100 mm).

What are standard pipe sizes?

NPSOutside Diameter (in)Weight (lb/ft)1/40.540″0.42 lb/ft3/80.675″0.57 lb/ft1/20.840″0.85 lb/ft3/41.050″1.13 lb/ft

How do I identify pipe threads?

Thread dimensions are based on the ID of the pipe. Use a caliper, measuring tape, or ruler to measure the thread diameter of a male thread or female thread. Measure the inner diameter (ID) of the female thread and the outer diameter (OD) of the male thread. This number will help determine the thread dimension.

Are bath mixer taps a standard width?

I am replacing standard taps with a Mixer tap. However their is a standard width between the pipes for most new Mixer taps 180mm.

What are the types of basin taps?

There are several types of basin taps that can give you functionality as well as fashion. You have single basin tap, wall basin tap, long basin tap, wash basin mixer tap, kitchen basin tap and bathroom basin tap that is all functional in their own way.

Are kitchen taps a standard fit?

Most tap units have a thread length standard with the existing connection alignment assured. So, when you’ve started the thread, tighten it but don’t overdo it. Screw-in the connector nuts to the mains pipe connections or fitted isolator valves. Then tighten once more with an adjustable open-ended spanner.

Are all kitchen taps the same?

If you have a free choice, your main decision is between having two separate taps (like pillar taps) or one single tap which mixes the water. While some people prefer a two-handle set-up to mix hot and cold separately, others prefer a single lever for ease of use and design.

How much does it cost for a plumber to change a tap UK?

Tap installation hourly rates The average rate for a plumber to fit a tap is around £40 – £60 per hour – depending on their experience, the complexity of the installation and where you live. For more information on prices, check out our guide to plumber costs.

Can you replace taps yourself?

This is a job you can do yourself, but just how do you fit new taps? This is one of those tasks which shouldn’t be too difficult or too expensive. Fitting new bathroom taps should be a straightforward enough project to take on yourself, so long as you use common sense and follow simple instructions.

Which type of tap is used in kitchen sink?

Kitchen sink taps fall into the following categories: Monobloc taps – feature a single lever handle or two handles. Pillar taps – supplied in pairs and a great budget option. Deck mixer taps – feature a single spout and use two tap-holes.

How do I choose a bathroom sink tap?

A simple rule for most basins is this: look for taps that extend as far as the plug hole. Lower spouts are good for smaller, cloakroom bathrooms where space is tight. Higher spouts make it easier to wash and shave. Longer spouts are suitable for larger bathrooms and basins where space isn’t an issue.

Are cheap taps any good?

Bad taps can make your life difficult, if not plain miserable, so buying cheap isn’t always a good choice. However, the price doesn’t always reflect the quality, so it’s important you look for taps that are built to a high standard and not necessarily just a high price.

Are Franke taps good quality?

Franke are a well-known appliance brand and their sinks and taps are particularly high-quality. … With plenty of options to choose from, there’s a Franke kitchen tap for any budget and any kitchen.

Which kitchen taps is best in quality?

  1. Heable Traditional Kitchen Mixer Tap: The best affordable monobloc kitchen tap. …
  2. Cooke & Lewis Gordale Bridge Mixer Tap: The best bridge-style kitchen tap. …
  3. Wenken Single Handle Solid Brass Monobloc Mixer Kitchen Tap with Pull Out Swivel Spout: The best pull-out spray kitchen tap.

How long should a basin spout be?

Most sink faucets have a spout reach of 5.5 inches on average but can go as high as 8 inches. We’re going to look at when 5.5 inches of spout reach works and when it won’t.