The tung oil and resin blend will saturate the wood surface leaving it very natural and unfinished looking while still providing excellent water and stain resistance.

What can you put over Waterlox?

Waterlox products can be applied over mineral oil as long as it is very dry. Wait at least 2 weeks after the last application of mineral oil. Wipe down the surface with a healthy amount of mineral spirits or paint thinner to help remove any residual mineral oil.

How do I remove a Waterlox finish?

  1. Razor blade knife;
  2. Acetone (nail polish remover); and/or.
  3. Chemical Paint Stripper.

Can you stain wood that has been sealed?

Your Wood Won’t Take Stain Because It’s Already Sealed

It is not a product that sits on top of the wood; it soaks in and dries in the wood pores. If you’re wood has already been sealed by polyurethane or another finish, the wood stain won’t work, because it can’t reach the pores of the wood.

Is Waterlox a polyurethane?

Our URETHANE formula is crystal clear and provides a rock-hard finish. Because there is no ambering with this product, the natural color of your wood floors, paneling, trim, cabinets, doors, bar tops and furniture shines through.

Can Waterlox be used over paint?

Waterlox Original Sealer/Finish may also be used on exterior wood surfaces as a sealer (only) to seal out moisture and intensify adhesion of the finish coat (latex and oil-base paints, or our Marine Finish).

Is Waterlox a varnish?

And Waterlox is varnish, specifically a phenolic resin/tung oil varnish.

What happens if you stain over sealed wood?

Yes, you can stain over varnish without any issue. But staining varnished wood is different than staining untreated wood. Clean and sand the wood using fine-grit sandpaper before applying stain over varnish to remove dust, debris and to emphasize wood grain which helps to take the stain better.

Can you use Waterlox over tung oil?

Waterlox ORIGINAL products are compatible with 100% PURE Tung Oil; provided the PURE Tung Oil has been applied and cured for over 30 days. … To prepare the surface for re-coating with Waterlox ORIGINAL Sealer/Finish (TB 5284), clean the surface with regular mineral spirits or paint thinner and allow to dry completely.

What happens if you don't seal stained wood?

Without sealer, the damage will typically be more apparent and likely to cause visible chipping. Finally, over time, stained wood without sealer will degrade faster. Wood that isn’t sealed loses color quality and stain uniformity much more quickly due to direct air and light exposure. It also warps and cracks faster.

Article first time published on

Can you stain before Waterlox?

Stain should only be mixed into the first coat of Waterlox sealer. This should be used as the base coat. Additional tinted layers can be used, but they may not color the wood as desired.

How long does it take for Waterlox to cure?

Allow each and every coat to dry for 24 hours. Dry time will depend upon ventilation, humidity and temperature. CURING Even though the recommended dry time is 24 hours, Waterlox Original Tung oil finishes completely cure in 30 – 90 days.

Is Waterlox good for Butcher block countertops?

Wood countertops can give your kitchen, bath or bar an unprecedented look. Waterlox is a superb choice for finishing wood countertops because it produces an incredibly appealing and durable surface. It is waterproof, food-safe and easy to maintain.

Can you sand Waterlox?

Waterlox must be coated with at least 12 hours of waiting time between coats. It is not necessary to abrade or sand lightly between coats, but if any of the coats are rough or have dust in them, light sanding is recommended to improve texture. Waterlox is a paint-thinner based finish; use paint thinner for all cleanup.

Can I wax over Waterlox?

Using Wax over Waterlox It is OK to use wax products over Waterlox finishes. Most buffing and application procedures should work absolutely fine over Waterlox finished surfaces, regardless of the final finish that is used.

How do I fix my Waterlox?

  1. Try using a rag dampened with mineral spirits to remove marks on the finish (such as black heel marks)
  2. For light scratches, clean the surface and apply a coat of finish.
  3. For deep gouges, use a small paint brush to fill in the gouge with finish to build it up and then feather the edges to blend in.

How long does Waterlox sealer last?

Waterlox finishes tend to wear very nicely and settle into a nice patina. They also will maintain a high level of protection even when worn (to a certain degree) due to the penetrating nature of the coatings. In general, the lifespan of an interior coating on a well-used surface will be 7-10 years.

Is Waterlox a good product?

Waterlox is an excellent choice for almost any kitchen, bath or bar project because it is easy to apply, repair and maintain.

Is Waterlox oil or water based?

A compromise that allows you to protect your floors while still appreciating the texture of the wood itself: a tung-oil blend called Waterlox. Even though the name contains the word “water,” this is not a water-based product; it is a penetrating resin-oil finish.

Is Waterlox just tung oil?

Waterlox Pure Tung Oil is 100% pure tung oil with no additives or driers. Produces a matte sheen appearance. Highlights and richens the natural beauty of wood.

Is Waterlox better than tung oil?

Better than pure tung oil or linseed oil, Waterlox is an excellent choice when you require the toughness and sheen of a varnish without the peculiarly plastic look of polyurethane.

What kind of finish is Waterlox?

Waterlox ORIGINAL Sealer/Finish is a resin-modified tung oil finish. Both the resin and the tung oil are amber in color and they provide a beautiful warmth to the surface.

Can you put tung oil over wax?

You never should have oiled over the wax. Just keep washing it down with the mineral spirits. You will know you have it all off when the rags you are using wipe clean. Then you will have to decide if you want to oil or wax it.

Can I use tung oil over polyurethane?

Once varnish hardens and cures, it’s impenetrable. When shopping for finishes, you might come across tung oil polyurethane. This product contains tung oil, but because it also contains polyurethane, it’s a varnish. You can’t use it and pure tung oil on the same piece of furniture.

Can you apply tung oil over shellac?

Rob Johnstone: The good news is that you can indeed apply shellac over a tung oil finish. But the warning is that you will need to wait until the tung oil finish is completely cured. That will take at least a week or so to be sure.

Is tung oil the same as mineral oil?

Food-grade mineral oil is a petroleum-based product that prevents wood from absorbing water. … Food-grade tung oil is made by pressing the seeds (often called nuts) of the tung tree. It’s naturally food-safe. Tung oil—which should be labeled 100% pure—is a little more expensive than food-safe mineral oil.

How do you apply Waterlox polyurethane?

Apply first coat of Waterlox URETHANE Finish with the grain and at the recommended spread rate. Allow to dry a minimum of 6 hours before applying another coat. If dry time is longer than 10 hours before applying another coat; sanding is REQUIRED. Good cross-ventilation is recommended.

Can you sand out mineral oil?

Keep in mind that mineral oil soaks deep into porous surfaces like wood, so you never really get all of it off your counter or cutting board. Sanding after you finish stripping it, however, can help you reach a nice starting point for adding new sealant.

Do I have to strip stain before restaining?

You don’t need to remove all of the old stain to apply darker stain. But you do need to remove all of the lacquer, varnish or anything that will prevent new stain from absorbing into the wood. … Your sanding block will initially glide over the old lacquer before it begins to cut into it and remove it.

Can you stain over Minwax Polycrylic?

Can you stain over Polycrylic? Yes, you can apply a tinted gel stain over a surface coated with Minwax Polycrylic Finish to give it your preferred shade. Ensure you sand the surface lightly and wipe off the debris before applying the gel stain.

Can I stain over Thompson's water sealer?

There is NO NEED TO REMOVE THE THOMPSON’S TO STAIN OR PAINT THE DECK OR RAILINGS. Follow the directions, You must wait at least 30-45 days (I recommend 6-12 months) before applying another product. The waterproofing nature of Thompson’s precludes using a water based product as a stain or paint.