The most standard tap thread for domestic taps in the UK is 3/4″ BSP. This measures 26.44mm across the outside diameter – roughly 1″ The picture shows the measurement for a standard 3/4″ tap thread. If your tap looks like this, you have a standard 3/4″ BSP tap.

How many MM is a garden tap?

Lastly, Garden Taps have a slightly different naming convention as well. A standard 15mm garden tap has a 15mm BSP Male threaded inlet and 20mm BSP Male threaded outlet. A 20mm garden tap has a 20mm BSP Male threaded inlet and 25mm BSP Male threaded outlet.

What is the standard tap size?

Nominal Diameter Range – InchesTap Dimensions – InchesOverTo(Incl.)Thread Length B.052 .065 .078.065 .078 .0915/16 1-3/8 7/16.091 .104 .117.104 .117 .1301/2 9/16 5/8.130 .145 .171.145 .171 .19711/16 3/4 7/8

What size is a standard garden tap in Australia?

Brass Tap – 1/2″ Male Inlet and 3/4″ Outlet This is the standard brass garden tap used in all states of Australia except NSW. For NSW use the 3/4″ x 1″ brass tap.

Are outside taps a standard size?

Taps used on farms, factories and in horticulture and fittings for garden irrigation pumps have a 1 inch or 7/8″ BSP outlet. Domestic plumbing fittings vary in diameter, but also have BSP threads.

What size are tap threads?

Standard taps are either standard coarse series threads NC (1/4-20), fine series threads NF (1/4-28) or extra fine series NEF (1/4-32). There are other standard tap designations such as NPT or NPTF for tapered pipe threads. Special taps are usually designated NS, indicating a special thread size.

How do you know what size your tap is?

The easiest way to find out the size of the thread in your mixer tap or faucet is to remove the aerator (this is the part that screws off at the end of your tap) and measure the diameter (across the centre) of the thread.

Is it easy to fit an outside tap?

It is normally easiest to fit the outside tap to a wall outside the kitchen as the mains water usually goes to the cold tap on the sink – to get an adequate water pressure at the end of a hose, the tap does need to be connected to the water mains not to a tank supplied, gravity feed.

What size is a garden tap washer?

The majority of inside taps take 12mm (1/2″) washers, while outside taps (garden taps) take 3/4″ (18mm).

What is a 1/2 inch tap?

Measuring BSP Sizes As an example, if you have a 1/2″ quarter turn ceramic disk tap valve, the 1/2″ refers to the thread on the cartridge that screws into your tap – it is this thread that will measure approx. 20.9mm across.

Article first time published on

What are the 3 types of taps?

  • There are 3 main types of taps to be familiar with Taper, Plug, and Bottoming tap.
  • The taper tap can be identified by the visible and pronounced tapering of the cutting edges. …
  • A plug tap has a less pronounced taper to the cutting edges.

Are all taps the same size?

Not all taps and countertop basins will be the same size, so you’ll want to make sure that there is adequate space from the top of your countertop basin to where the spout exits on the tap. Finally, make sure that you have enough space on your counter to mount your tap behind your basin.

How do you measure a hose connector tap?

If you’re wondering how you can measure the size of your tap or any fitting you may already have to help you buy the matching connectors; here you go. Take a tape and measure the inside diameter of the fitting for female threads while you measure the outside diameter of the fitting if it has a male thread.

What is a taper tap?

Taper: Taper Taps typically have 8 -10 threads that are tapered. The shape of this tap helps the thread to start. They can be used to start a thread before using a plug or bottom tap. … A bottoming tap has nearly no taper with a thread count of 1-2.

What is the minor diameter of thread?

The minor diameter is the lower extreme diameter of the thread. Major diameter minus minor diameter, divided by two, equals the height of the thread. The minor diameter of a nut is its inside diameter.